Showing posts with label simple. Show all posts
Showing posts with label simple. Show all posts
Simple Adjustable Notch Filter Circuit Diagram
Adjustable Notch Filter Circuit Diagram. In applications where the rejected signal might deviate slightly from the null on the notch network, it is advantageous to lower the Q of the network. This insures some rejection over a wider range of input frequencies. The figure shows a circuit where the Q may be varied from 0.3 to 50. A fraction of the output is fed back to R3 and C3 by a second voltage follower, and the notch Q is dependent on the amount of signal fed back. A second follower is necessary to drive the twin `T` from a low-resistance source so that the notch frequency and depth will not change with the potentiometer setting.
Adjustable Notch Filter Circuit Diagram

Wiring Switches Rules Simple Connect Wire
Wiring Three Way Switches The Rules Are Simple Connect The Hot Wire.
Home House Wiring Installation.
And Then We Get To Our Homes And Offices.
Home Electrical Wiring New Home Remodels Additions As You Wish.
Home Wiring Diagram.
House And Home Wiring Diagram And Electrical System Png.
Wiring Diagram.
Solar House Wiring Diagram Jpg.
Slim Films House Illustrations.
Home Wiring Diagrams Wiring Diagrams Typical Alarm System Wiring.
Simple Flasher circuit diagram
Most of you asked about a LED flasher circuit.Here it is.Here I have used famous IC LM3909.This circuit operates with 1.5V

Read Full article[...]

Simple Peak Indicator
A simple circuit, peak indicator of tops of musical signal. Each time where the level of signal exceeds the level + 4dB, turns on led D1. It is useful in each channel of console of sound, in final amplifiers or in that other application, to we needed. With the prices of circuit, the indicate begins with levels above + 4 dB (1.25V rms). For adaptation in different levels of signal, we can use a trimmer, before capacitor C1.
Peak Indicator Circuit Diagram :
R1 = 10K
R2 = 1.2K
R3 = 220K
R4 = 4.7K
R5 = 4.7K
C1 = 47uF-25V
C2 = 2.2uF-25V
Q1 = BC550C
Q2 = BC550C
D1 = Red LED
Notes:
- It can be assembled on a general purpose PCB.
- It can be powered from a 12V-15V regulated power supply.
Source : www.ecircuitslab.com/2011/05/simple-peak-indicator.html
Simple Transformerless 5 Volt Power Supply
Description
An increasing number of appliances draw a very small current from the power supply. If you need to design a mains powered device, you could generally choose between a linear and a switch-mode power supply. However, what if the appliance’s total power consumption is very small? Transformer-based power supplies are bulky, while the switchers are generally made to provide greater current output, with a significant increase in complexity, problems involving PCB layout and, inherently, reduced reliability.
Is it possible to create a simple, minimum part-count mains (230 VAC primary) power supply, without transformers or coils, capable of delivering about 100 mA at, say, 5 V A general approach could be to employ a highly inefficient stabilizer that would rectify AC and, utilizing a zener diode to provide a 5.1 V output, dissipate all the excess from 5.1 V to (230×v2) volts in a resistor. Even if the load would require only about 10 mA, the loss would be approximately 3 watts, so a significant heat dissipation would occur even for such a small power consumption.
At 100 mA, the useless dissipation would go over 30 W, making this scheme completely unacceptable. Power conversion efficiency is not a major consideration here; instead, the basic problem is how to reduce heavy dissipation and protect the components from burning out. The circuit shown here is one of the simplest ways to achieve the above goals in practice. A JVR varistor is used for overvoltage/surge protection. Voltage divider R1-R2 follows the rectified 230 V and, when it is high enough, T1 turns on and T3 cannot conduct.
Circuit diagram:

When the rectified voltage drops, T1 turns off and T3 starts to conduct current into the reservoir capacitor C1. The interception point (the moment when T1 turns off) is set by P1 (usually set to about 3k3), which controls the total output current capacity of the power supply: reducing P1 makes T1 react later, stopping T3 later, so more current is supplied, but with increased heat dissipation. Components T2, R3 and C2 form a typical ‘soft start’ circuit to reduce current spikes this is necessary in order to limit C1’s charging current when the power supply is initially turned on. At a given setting of P1, the output current through R5 is constant.
Thus, load R4 takes as much current as it requires, while the rest goes through a zener diode, D5. Knowing the maximum current drawn by the load allows adjusting P1 to such a value as to provide a total current through R5 just 5 to 6 mA over the maximum required by the load. In this way, unnecessary dissipation is much reduced, with zener stabilization function preserved. Zener diode D5 also protects C1 from over voltages, thus enabling te use of low-cost 16 V electrolytics.
The current flow through R5 and D5, even when the load is disconnected, prevents T3’s gate-source voltage from rising too much and causing damage to device. In addition, T1 need not be a high-voltage transistor, but its current gain should exceed 120 (e.g. BC546B, or even BC547C can be used).
CAUTION!
The circuit is not galvanically isolated from the mains. Touching any part of the circuit (or any circuitry it supplies power to) while in operation, is dangerous and can result in an electric shock! This circuit should not be built or used by individuals without proper knowledge of mains voltage procedures.
Copyright: Elektor Electronics Magazine
Author: Srdjan Jankovic & Branko Milovanovic
Author: Srdjan Jankovic & Branko Milovanovic
Subscribe to:
Posts (Atom)